Question: How do I find electrical wires in the wall?

There are two kinds of stud finders that can help you find wires in a wall – magnetic and electric. A magnetic stud finder is used to detect metal nails in wall studs. Electronic stud finders produce a tiny electrical field that changes when the finder reaches a denser region in a wall.

How do I know where the wires are in the wall?

Use your electric wire detector to find out exactly where the wires run through the walls. Use the wire detector and concentrate on the specific areas where you suspect wires to be. A wire detector is simply a type of metal detector that is able to detect the presence of metallic objects in your walls.

How do you find electrical wires behind drywall?

By pressing the stud finder power button and gradually moving it slowly across the area, a stud, a pipe, or a wire inside the wall will trigger a beeping signal, which one will be confirmed with an indicator light in Figure 6 flashing on the scanner.

Is there a tool to find wires in walls?

The Meterk Wire Tracker is a powerful and reliable device that traces a wide range of wires, those located both behind walls and those buried underground. It also checks the status of network and telephone lines.

How do you trace live electrical wires?

0:123:29How to Find Wires | Using a Wire Tracer - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou can look for wire tracers that are made for live wires. These are typically more expensive. ButMoreYou can look for wire tracers that are made for live wires. These are typically more expensive. But they can come in handy. Especially. If youre tracing say AC wiring in your home.

Do stud finders detect wires?

All stud finders do the same basic thing, using either electronic sensors or magnets: They detect where support areas like studs and joists are inside the walls. All stud finders can detect wood, most detect metal, and many also detect live electrical wiring.

How far into the wall are wires?

How far into the wall are wires located? Wiring usually runs horizontally, about an inch into the wall. The parameters are 6 inches or 12 inches above the receptacle.

How far behind drywall are wires?

Wires. Electrical cables are usually behind drywall, either running horizontally through holes in the studs or stapled vertically up the sides of studs. Outlet cables tend to be about 12 inches high. Light switches are around 48 inches high, so expect to see electric cables around that area.

Do electric wires run up or down?

Electrical wires typically run either vertically, up and down the side of a stud or horizontally. The vertical wires are typically pretty easy to avoid: avoid drilling above a receptacle or light switch.

How do stud finders detect wires?

More advanced stud finders called “multi-scanners” are designed to find electrical wires using a small radar that also has metal detecting radars. As your stud finder runs along the wall, if it comes across as stud that has live wiring running through it, the beeping will turn more into a screeching sound.

How do you trace electrical wires without electricity?

To find wires without any power one of the handiest tools is an electronic stud finder. Most stud finders are equipped to handle finding wooden studs in the wall, but some can also be used to find wires as well. To find out if a wire is live, youll also need a voltage detector.

Why are stud finders so unreliable?

Most magnet-type stud finders dont work effectively since they reply on locating the fasteners (screws) used to secure the drywall. These can be very difficult to locate.

What happens if you drill into a wire?

Damage to electrical wiring from drilling into walls is a surprisingly frequent phenomenon – especially when buildings are being renovated. In the worst case, if the protective earth conductor has been damaged you otherwise run the risk of a fatal electric shock.

Can you drill anywhere in a wall?

One rule of thumb is to be especially careful when drilling into any walls that connect to your bathroom or kitchen—basically, any wall thats likely to have pipes. “And unless you hit it where it passes through a stud, your drill bit will probably deflect off of the curved surface.”

How do I make sure I dont drill into a wire?

16:3326:258 TIPS to avoid Pipes and Cables in Walls (long rambling version)YouTube

What happens if you nail into a wire?

When hammering in nails, it is best to drive them into a wall stud. According to, most homes have wires and pipes behind the walls, and there are no guarantees as to their locations. Hitting a wire or pipe could cause serious injuries to the person holding the drill and could damage the home as well.

Can I use my iPhone as a stud finder?

The iPhone beeps when its magnetometer, in the upper right of the phone, is near metal. Stud Find is an iPhone application that uses the devices built-in magnetometer to find metal studs, screws, nails and anything metallic in a wall.

Are cheap stud finders accurate?

I was pleasantly surprised to find that the majority of stud finders I tested were accurate and dependable. The ones that werent didnt make this list. The following stud finders detect anything from steel fasteners to live wires and pipes. Some even detect double-stud construction.

Where can you not drill into walls?

Avoid drilling near light sockets or outlets Wires in the wall often connect vertically and horizontally behind outlets and sockets and can lead to electrocution. Hitting a pipe in the wall can cause flooding. A simple rule of thumb is to avoid drilling anywhere near where there may be electrical hookups or piping.

How do you check if you can drill into a wall?

To find a safe spot to drill into, you need to move the device across the wall with equal pressure. Always keep in mind that you should only move it along the x-axis. So, if you are moving the device horizontally across the wall, you should grip the device from below.

Say hello

Find us at the office

Hostler- Pertzborn street no. 57, 67563 Kigali, Rwanda

Give us a ring

Anterio Ruebush
+29 780 790 988
Mon - Fri, 8:00-17:00

Contact us